OPTIMA-R-FC

OPTIMA-R

Systemair Navigation Global

Vilkår for Webshop

Kontakt & Support

Luftfordelingsprodukter

Produkter

Norway

Systemair Norge

Enkel sonekontroll

Fabrikkkalibrert

Robust

OPTIMA-R er sirkulære VAV-spjeld som ofte brukes til avtrekk, men også til tilluft ved lavt systemtrykk. Spjeldene er ideelle for sonestyring med tilluft og avtrekk i et master/slave-arrangement. OPTIMA-R installeres vanligvis i kontorer, hotellrom og møterom hvor kjøle- og varmebelastningen vil variere etter behov.

VAV-spjeldhuseter laget av galvanisert stål. Den spesielle utformingen av målekrysset sikrer luftstrømavlesning med stor nøyaktighet, selv der installasjoner er vanskelige. VAV spjeldene er fabrikkkalibrert til standard luftvolum, men kan på forespørsel justeres til ønsket innstilling før utsendelse i Vmin- og Vmax-området. Dette må angis før bestilling av spjeld. Gateway-kommunikasjonsenheter  for kobling til bygningsstyringssystem kan også leveres.

OPTIMA-R-FC is a variable air volume (VAV) controller with or without insulation. The product is intended to control the air pressure in a ventilation system. The product is installed into circular ducts. Field of application is e.g. offices, hotel rooms, meeting rooms or larger public or industrial halls where the required cooling and heating load will vary on demand.

• Damper tightness class 4 according to EN 1751

• Casing tightness class C according to EN 1751

• Conform with hygienic requirements according to VDI 6022

• High measurement/control accuracy in 5% deviation range

• Air volume range of 36 m3/h to 12344 m3/h

• Operating range of duct pressure up to 1000 Pa

• OPTIMA-RI-FC version with external insulation for radiated sound reduction

: Circular VAV Controller with Acoustic Insulation

 Configuration and setup tool for VAV controllers OPTIMA-...B…

 Configuration and setup NFC app. for Android smartphones for OPTIMA-…BP

 Converter Bluetooth/NFC smartphones to configure OPTIMA-…BP in Belimo Assistant app.

OPTIMA-R-FC consists of a casing, a damper blade and a measurement probe. The casing is manufactured from galvanized sheet steel. The casing contains a duct connection with a rubber gasket. The damper blade is manufactured from extruded aluminium. The blade is equipped with a rubber gasket. The gasket eliminates leakage in the closed position. The aluminium measurement probe is connected to the VAV controller with flexible polyurethane impulse tubing. The special design of the multi-point averaging cross-flow sensor assures accurate air flow readings. OPTIMA-RI-FC has 19 mm thick polymer foam insulation around the casing. The insulation is covered by a galvanized steel protection sheet.

The VAV controllers are as standard equipped by compact controllers/actuators with analog setpoint and feedback signals in mode DC 2 V … 10 V or DC 0 V … 10 V. The compact controllers are equally available with MP-BUS, MODBUS, BACnet and KNX communication capability. On demand as an alternative, Gateway communication units can be provided and can be connected later to building management systems (only possible with MP-BUS communication on board). VAV compact controllers are factory calibrated as standard to the default air volume. Upon request, the VAV controllers can be adjusted to site-required settings prior to dispatch on Vmin and Vmax range. The air volumes can also be readjusted on site with the ZTH-EU handheld service tool or, for the type OPTIMA…GM… by dials on the controller. If specific air volumes for Vmin and Vmax are required, this must be indicated before the order of the units for adequate calibration in the factory.

• BP: Belimo LMV-D3 compact controller with MP-BUS communication and analog 0 (2) V … 10 V setpoint and feedback signals. NFC communication port is available for the device configuration by the “Belimo Assistant” smartphone application.

• BA: Belimo LMV-D3 compact controller without BUS communication and with analog 0 (2) V … 10 V setpoint and feedback signals.

• BM: Belimo LMV-D3 compact controller with selectable Modbus RTU and BACnet MS/TP bus communication, MP-BUS communication and analog 0 (2) V … 10 V setpoint and feedback signals.

• BK: Belimo LMV-D3 compact controller with KNX bus communication. The controller uses S-Mode (System mode) as the KNX communication mode.

• GM: Compact controller with parametrizing dials and display for immediate adjustment on site, communicative via Modbus-RTU and with analog 0 (2) V … 10 V setpoint and feedback signals.

The classification is done according to the standard EN 1751 for static pressure up to 1000 Pa.

OPTIMA-R-FCVariabel Volumregulering

Enkel sonekontroll

Fabrikkkalibrert

Robust